From KTMTalk:
http://ktmtalk.com/index.php?showtopic=374413
This would appear to work on most motos. Concern would be that the frame extends below the swingarm pivot so as to protect the zerks.
The KTM RFS bikes use two needle bearing on each side of the swingarm with a small gap between eache pair. Pushing grease into the gap would force the old greaase out and take contaminants with it.
Here is a pic of the RFS suspension for a visual.
adding zerk grease fittings to the swingarm
adding zerk grease fittings to the swingarm
Safiri Mike
Current: 01 F650-GSDakar-RWB; 02 EXC-453 (orig. MXC 400); 05 EXC-450 ; 13 CRF-250L; 17 CRF-125FB; 06 KLX-110 (132); 02 TTR-125L
Gone and missed (but no regrets): 01 LC4E-400-Grey
Gone and not missed: 73 AT3, 85 K100RS
Current: 01 F650-GSDakar-RWB; 02 EXC-453 (orig. MXC 400); 05 EXC-450 ; 13 CRF-250L; 17 CRF-125FB; 06 KLX-110 (132); 02 TTR-125L
Gone and missed (but no regrets): 01 LC4E-400-Grey
Gone and not missed: 73 AT3, 85 K100RS
Re: adding zerk grease fittings to the swingarm
I think my Honda came with one factory. The YZ didn't though, and when I rebuilt it, the bearings were powdered rust.
Re: adding zerk grease fittings to the swingarm
I put zerks in my mid eighties Husky's, a small hole drilled in the end of the pivot bolt and exits between the inner bearing races. I had to drill a little bigger to tap in a 1/16"-27 NPT zerk, actually a 1/4"-28 tap works just fine. I normally had them plugged with allen setscrews and didn't ride with the zerks in place, too close to my ankle bones.
My old Honda xrl has zerks, no such thing as too easy!
My old Honda xrl has zerks, no such thing as too easy!
Re: adding zerk grease fittings to the swingarm
The hollow swingarm bolt would be great, except for bike like the RFS that use a sleeve between the bolt and the bearing. So check it out before you go to the trouble of drilling your bolt!katbeanz wrote:I put zerks in my mid eighties Husky's, a small hole drilled in the end of the pivot bolt and exits between the inner bearing races. I had to drill a little bigger to tap in a 1/16"-27 NPT zerk, actually a 1/4"-28 tap works just fine. I normally had them plugged with allen setscrews and didn't ride with the zerks in place, too close to my ankle bones.
My old Honda xrl has zerks, no such thing as too easy!
Good call on removing zerks to save your ankles!
Safiri Mike
Current: 01 F650-GSDakar-RWB; 02 EXC-453 (orig. MXC 400); 05 EXC-450 ; 13 CRF-250L; 17 CRF-125FB; 06 KLX-110 (132); 02 TTR-125L
Gone and missed (but no regrets): 01 LC4E-400-Grey
Gone and not missed: 73 AT3, 85 K100RS
Current: 01 F650-GSDakar-RWB; 02 EXC-453 (orig. MXC 400); 05 EXC-450 ; 13 CRF-250L; 17 CRF-125FB; 06 KLX-110 (132); 02 TTR-125L
Gone and missed (but no regrets): 01 LC4E-400-Grey
Gone and not missed: 73 AT3, 85 K100RS